7LEGENDARY

7 LEGENDARY

Best CS2 Launch Options and Autoexec Setup Guide

Set up CS2 launch options and autoexec.cfg, adjust FPS limits, avoid outdated binds, and verify your settings with this step-by-step guide.

Guides · By Rizky Mardiyansyah Aries ·

Setting up CS2 launch options and an autoexec file helps keep your Counter-Strike 2 settings consistent whenever you start the game. Some commands carried over from CS are now obsolete, and Valve has restricted certain automated binds.

This guide covers useful startup parameters, a basic CS2 autoexec configuration, and how to check that everything loads correctly.

How CS2 Launch Options and Autoexec Work

Launch options are instructions Steam passes to CS2 when the game starts. They can request fullscreen mode or execute a configuration file.

An autoexec.cfg file contains console commands for settings such as FPS limits and network rate. Keeping these commands in one file makes them easier to review and change.

For this setup, Steam handles startup instructions while autoexec stores the FPS setting. There's no need to specify the same value twice.

Best CS2 Launch Options

Open Steam and follow these steps:

  1. Go to Library and right-click Counter-Strike 2.

  2. Select Properties.

  3. Find Launch Options under General.

  4. Enter:

-fullscreen +exec autoexec.cfg

-fullscreen requests fullscreen mode. It doesn't guarantee higher FPS or lower input latency.

+exec autoexec.cfg tells CS2 to execute your configuration file at startup. The file must be saved in the correct directory.

Avoid copying old CS launch options without checking them. For example, -tickrate 128 cannot change the tickrate of official CS2 matchmaking servers. CS2 uses a sub-tick system, which this parameter doesn't override.

CS2 Autoexec Setup

Create the Configuration File

  1. Open File Explorer.

  2. Navigate to your CS2 installation directory:

Steam\steamapps\common\Counter-Strike Global Offensive\game\csgo\cfg
  1. If Steam uses another drive, find the installation through Properties → Installed Files → Browse.

  2. Open Notepad and create a new document.

  3. Paste the configuration below.

  4. Select File → Save As.

  5. Enter autoexec.cfg as the filename.

  6. Set Save as type to All Files, then save it inside the cfg folder.

Check that Windows hasn't saved the file as autoexec.cfg.txt. Enable file extensions in File Explorer if necessary.

Basic Autoexec Configuration

// FPS limit: example value
fps_max "160"

// Network rate: default maximum
rate "786432"

// Startup confirmation
echo "7Legendary CS2 Autoexec Loaded"

The 160 FPS cap is an example. Choose a value your PC can maintain consistently, especially if you experience fluctuating frame times.

Restart CS2 after saving the file.

Why Jumpthrow Binds Are Excluded

On 19 August 2024, Valve restricted binds combining multiple movement or attack actions. These include traditional jumpthrow binds.

Valve said suspected input automation could result in players being kicked from official matches. It also stated that jumpthrows can be performed consistently through manual input without special scripts.

Remove outdated automated binds from older configurations. The example autoexec above doesn't include any jumpthrow scripts or movement automation.

Read also: EA FC 27 Meta Formations and Pro Custom Tactics

FPS, Network Settings and Sub-Tick

Choosing an FPS Limit

fps_max controls the game's maximum framerate. The example autoexec uses a cap of 160 FPS.

To remove this command's FPS limit, use:

fps_max "0"

An uncapped framerate isn't automatically better. If your PC experiences inconsistent frame times, test a sustainable FPS cap against uncapped performance under similar gameplay conditions.

Another command you may see in frame-pacing guides is:

engine_low_latency_sleep_after_client_tick "1"

According to TotalCSGO, its documented default is 0, and it affects sleep timing when r_low_latency is enabled. Its benefit needs testing on the relevant system, so it isn't included in the basic configuration.

Check its current value through the developer console before changing it.

Network Rate

The rate command controls the client's incoming data-rate limit. According to TotalCSGO, 786432 is already the default and maximum value. The line in the example autoexec simply makes that setting explicit. It won't fix packet loss caused by an unstable connection or server problems.

How Sub-Tick Works

CS2's sub-tick system records the timing of player actions between server ticks. It operates without a special launch option, and players cannot change official matchmaking servers to 128 tick using -tickrate 128.

Best CS2 Launch Options and Autoexec Setup Guide.

Verify Your Autoexec and Fix Problems

Check That Autoexec Loads

  1. Open Counter-Strike 2.

  2. Go to Settings → Game and enable Developer Console.

  3. Open the console using your assigned key, usually ~.

  4. Look for the confirmation message:

7Legendary CS2 Autoexec Loaded
  1. Enter fps_max to check the active FPS limit.

If the confirmation message doesn't appear, run:

exec autoexec.cfg

If manual execution works, check your Steam launch options. Otherwise, verify the file location and .cfg extension.

Undo the Configuration

  1. Close Counter-Strike 2.

  2. Open the folder containing autoexec.cfg.

  3. Rename the file autoexec_backup.cfg.

  4. Open Steam → Counter-Strike 2 → Properties → General.

  5. Remove +exec autoexec.cfg from Launch Options.

  6. Restart CS2 and check whether the problem has been resolved.

You can also edit individual commands without removing the entire file.

Tags: cs2 launch options, best cs2 launch options, cs2 autoexec, cs2 autoexec setup, autoexec.cfg, cs2 fps settings, cs2 performance guide, counter-strike 2 launch options

More Guides stories

Latest news